SIM2 MultimediaLumis 3D-SUser Guide
◦ Memories◦ 3D Controls (3D Mode and Input Formats)OperationThe Lumis 3D-S projector has two IR receivers, one on the front and one on the back of the
Connections❶ ❷ ❸ ❹ ❺ ❻❼ ❽Inputs❶HDMI 1HDMI 2Accept both HDMI and DVI digital video inputs.❷Components/RGB-HV Four RCA connectors. They accept both sta
3D IR EmitterThe 3D infrared emitter is designed to be placed near the projector and aimed at the screen. It receives the 3D sync signal from the proj
3 InstallationThis section provides instructions for the installation of the Lumis 3D-S projector.Important: Installation procedures should be perform
Ceiling MountingInvert the projector and suspend it from the ceiling using a specific bracket.• To fit the bracket unscrew and remove the 3 rubber fee
If it is not possible to position the projector perpendicular to the projection screen (so that the lens center and screen cen-ter are aligned with ea
throughout the entire signal path◦ highest available resolution, because video sources can deliver full resolu-tion content via HDMI only◦ availabilit
Note: RS-232 communications are limited to 15 m (50 ft.), whereas USB are limited to 5 m (16 ft.).TriggersSome Home Theater devices can be controlled
Switching On and OffSwitching On1. Turn on the main power switch on the right hand side of the projector. The projector enters the low power Standby s
4 OperationViewing 3D Content3D stereo visualization offers clear and sharp 3D images thanks to 3 chip DLP Imaging technology. This technique achieves
Contents3 Important informationSafety3D contentEnvironmentNotice7 Chapter 1: IntroductionKey Features and BenefitsSystem ComponentsOptional Accessorie
select the correct one.• Switch on your 3D glasses. Refer to the instructions supplied with the glasses to ensure correct operation.• The projector wi
• 2D display mode for normal 2D material. 3D Input Format adjustment is un-available. PureMotion adjustment is available.3D Input FormatThe Lumis 3D-S
Table 4.1Signal 3D Format HDMI 1.4a DVB1920 x 1080p @ 23.98/24 Hz Frame Packing YesSide by Side YesTop and Bottom Yes Yes1920 x 1080p @ 25 Hz Side by
• To enter the Input menu press:Key 0 on the remote control or Source on the projector keypad.• To select an input press the corresponding number on t
PictureThis menu section provides access to common image quality adjustments. Adjust-ments not available for a given input are not displayed in the me
ColorThis control (also called Saturation) increases or decreases the picture color intensity. When set to zero, color images are shown in black and w
DynamicBlackThis function improves the level of black and increases the depth and the detail of the image especially in parts with low and medium brig
• Letterbox displays a 4:3 letterbox image (source signal with black bands above and below the picture) in such a way that it fills the 16:9 screen an
◦ User a white point that can be adjusted according to your personal prefer-ences as follows:▪ press the number 3 on the remote control to activate th
manually and move sufficiently close to the screen to observe the effects of the ad-justments.Y/C DelayWhere Video signals are concerned, use this adj
Important informationSafetyTo reduce the risk of electrocution, disconnect the power cord on the rear panel before removing the top cover of the proje
3D GlassesSelects the type of active shutter glasses you are using. Choose: • SIM2 (the default setting) when you are using the 3D glasses (103-S) and
(which is undesirable if you are using a custom control system).You can change the label of each input (for example assigning the name of the device i
2. use ◂, ▸, ▴ or ▾ for a finer adjustmentNote: Avoid locations too close to corners or edges to prevent cropping of larger menus.OSD Display TimeoutS
3. press ● to open the corresponding pull-down menu4. press ▴ and ▾ to highlight Save current settings5. press ▸ to executeThe confirmation message “C
Important: When you enter the Memories menu, a copy of the current setting for the active input is saved in a temporary memory, numbered 0 and called
5 TroubleshootingThe projector does not turn on• Make sure the main power switch (at the rear of the projector) is in the On position.• Ensure the pro
3D content is displayed as two near-identical images• If they are next to each other, press the 3D key on the remote control and then choose Side by S
6 SpecificationsProjection Type Digital Light Processing (DLP), 3-chipDLP Type: 0.95 in., 1920 x 1080, DC4Optical Engine Die cast, based on SIM2 paten
Video Standards Composite: NTSC 3.58/4.43, PAL B/G/H/I/M/N/60, SECAM (automatically selected) Components/RGBHV: 480i, 576i, 480p, 576p, 1080i 50/60
7 Projection Distances1.78:1 (16:9) ScreenScreenProjection DistanceVerticalOffset(m)T1 (1.37-1.66:1) T2 (1.75-2.48:1) T3 (2.54-3.90:1)Diagonal Size (i
with a flat head screwdriver and replace the fuse. Fit the replacement fuse. Use only type T 10 A L H fuses for the projector.Be careful with cablesMa
8 DimensionsLumis 3D-S dimensions in millimeters and (inches).8 Dimensions Lumis 3D-SUser Guide40
SIM2 Multimedia S.p.a.Viale Lino Zanussi, 11 33170 Pordenone – ITALYPhone: + 39 434 383256 Fax: +39 434 383260Email: [email protected] USA1
3D contentDiscomfort (such as eye strain, headaches, motion sickness, nausea, dizziness, disori-entation) may be experienced while watching 3D content
Product disposalThe lamp inside this projector contains mercury and may be subject to special disposal or recycle regulations. Dispose or recycle in a
1 IntroductionThe Lumis 3D-S is a high-end compact 3-chip DLP 3D single unit projector that utilizes SIM2’s state-of-the-art optical technologies to p
If any items are missing or damaged, contact your SIM2 Authorized Dealer as soon as possible. Keep the original packaging in case anything has to be s
2 OverviewRemote Control❶Turn backlight on for about 5 seconds❶❸❹❺❼❽❾⓫⓬⓮❷❻❿⓭⓰⓯❷ turns the projector off❸1-9select inputs and turn the projector on
Commentaires sur ces manuels