Sim2 C3X1080 Manuel d'utilisateur télécharger pdf (Page 19)

C3X1080

ENGLISH

USING A MEMORY

To use a Memory, select the line in question and press

the . key. The settings stored in the memory you have

selected will be applied to the projected image, while a

message will confirm that Memory has been applied. The

memory will be associated with the particular source and

signal type and will be automatically applied whenever

that particular combination of source and signal type is

selected.

RESTORE INITIAL SETTINGS FOR A MEMORY

When you need to restore the initial settings in a Memory

that has previously been modified, select the line referring

to the Memory in question and open the correspond-

ing pull-down menu (key ▶). Then select the “Save initial

settings” line. A message stating “Initial settings saved in

Memory 1” will appear at the bottom of the display

RENAME A MEMORY

All Memories can be named. To assign a name (with a

maximum length of 12 alphanumeric characters) to a

Memory, select the Rename option from the correspond-

ing pull-down menu. Enter the text as described in the

paragraph

ENTERING TEXT

RESTORE CURRENT VALUES

When you enter the

MEMORIES

menu a copy of the current

settings is saved in a temporary memory (marked

0 - AUTO

Once one or more memories have been recalled, you

can restore the settings that were effective at the moment

the Memories menu was accessed by selecting

Memory

‘0’ (

0 - AUTO)

. Note that this operation must be executed

before the

Memories

menu page disappears (30 seconds

after last operation with the remote control or keypad).

The next time it appears, in fact, the temporary memory

will contain new information that takes account of any

Memories selected on the last time but one that the

MEMORIES

page was accessed.

Memory 0 can be used even when you do not wish to

enable Memories management for the signal in use. In

fact, once Memory 0 has been selected, when a source

is chosen, the settings that were effective at the time the

Memory was previously recalled will be automatically

applied.

INFO

Displays the current operating status of the projector and

information concerning the projected video/graphic

signal.

This function is displayed by pressing the

key on the

remote control (or, when the On Screen Display is not

enabled, the ▶ key on the keypad).

QUICK MENUS

The quick menus provide access to the main adjustments

that affect image quality without opening the main menu.

BRIGHTNESS

CONTRAST, COLOUR, TINT, SHARPNESS

and

FILTER

adjust-

11 CLEANING AND MAINTENANCE

The projector does not require internal adjustment. There

are no user serviceable parts inside the projector.

To replace the bulb or any other repairs, contact your local

service centre, whose engineers will be happy to efficiently

solve any problem.

Use a soft cloth to clean the projector housing, if neces-

sary slightly dampened with water and a small amount of

neutral soap. Do not rub the rear panel markings.

The lens may be cleaned with a small very soft, non-

abrasive brush, to remove dust particles. Alternatively, use

a soft dry cleaning cloth (of the type used for camera lens

cleaning) to remove fingerprints and grease marks.

12 TROUBLESHOOTING GUIDE

NO POWER (LEDS ALWAYS OFF)

• Check that the projector’s power switches are set to

• Check that the power cables are correctly connected

to the projector’s power sockets.

• Check the condition of the fuse located next to the

power socket at the rear of the projector.

• Replace the fuse located on the projector’s power socket

ments appear at the bottom of the screen one after the

other when the ▼ and ▲ keys are pressed.

MESSAGES

The following messages may appear on your screen:

NO SIGNAL

The system does not recognise any signal applied to the

selected input. In this case:

• Make sure the selected input is connected to a video

or graphic signal and that that source is functioning

correctly.

• Check the condition of the cables used to connect

the system to the various sources.

• Make sure the video or graphic signals supplied by

the source are compatible with the system’s techni-

cal specifications and, in particular, with those of the

selected input.

OUT OF RANGE

This message appears when either the resolution or the

vertical/horizontal frequency of the input signal exceeds

system specifications (e.g. a QXGA graphic signal) or

when an input is supplied with an incompatible signal

(e.g. if a progressive signal is connected after setting the

components input to YCrCb 15kHz).

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 28 29

Commentaires sur ces manuels

Pas de commentaire

Sim2 C3X1080 Manuel d'utilisateur Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Projecteurs Sim2 C3X1080